man/orig/inetd
Материал из Xgu.ru
Не указан параметр (1)
INETD(8) FreeBSD System Manager's Manual INETD(8)
Содержание |
[править] NAME
inetd -- internet ``super-server
[править] SYNOPSIS
inetd [-d] [-l] [-w] [-W] [-c maximum] [-C rate] [-a address | hostname]
[-p filename] [-R rate] [-s maximum] [configuration file]
[править] DESCRIPTION
The inetd utility should be run at boot time by /etc/rc (see rc(8)). It
then listens for connections on certain internet sockets. When a connec-
tion is found on one of its sockets, it decides what service the socket
corresponds to, and invokes a program to service the request. The server
program is invoked with the service socket as its standard input, output
and error descriptors. After the program is finished, inetd continues to
listen on the socket (except in some cases which will be described
below). Essentially, inetd allows running one daemon to invoke several
others, reducing load on the system.
The following options are available:
-d Turn on debugging.
-l Turn on logging of successful connections.
-w Turn on TCP Wrapping for external services. See the
IMPLEMENTATION NOTES section for more information on TCP Wrappers
support.
-W Turn on TCP Wrapping for internal services which are built in to
inetd.
-c maximum
Specify the default maximum number of simultaneous invocations of
each service; the default is unlimited. May be overridden on a
per-service basis with the "max-child" parameter.
-C rate
Specify the default maximum number of times a service can be
invoked from a single IP address in one minute; the default is
unlimited. May be overridden on a per-service basis with the
"max-connections-per-ip-per-minute" parameter.
-R rate
Specify the maximum number of times a service can be invoked in
one minute; the default is 256. A rate of 0 allows an unlimited
number of invocations.
-s maximum
Specify the default maximum number of simultaneous invocations of
each service from a single IP address; the default is unlimited.
May be overridden on a per-service basis with the "max-child-per-
ip" parameter.
-a Specify one specific IP address to bind to. Alternatively, a
hostname can be specified, in which case the IPv4 or IPv6 address
which corresponds to that hostname is used. Usually a hostname
is specified when inetd is run inside a jail(8), in which case
the hostname corresponds to that of the jail(8) environment.
When the hostname specification is used and both IPv4 and IPv6
bindings are desired, one entry with the appropriate protocol
type for each binding is required for each service in
/etc/inetd.conf. For example, a TCP-based service would need two
entries, one using ``tcp4 for the protocol and the other using
``tcp6. See the explanation of the /etc/inetd.conf protocol
field below.
-p Specify an alternate file in which to store the process ID.
Upon execution, inetd reads its configuration information from a configu-
ration file which, by default, is /etc/inetd.conf. There must be an
entry for each field of the configuration file, with entries for each
field separated by a tab or a space. Comments are denoted by a ``# at
the beginning of a line. There must be an entry for each field. The
fields of the configuration file are as follows:
service-name
socket-type
protocol
{wait|nowait}[/max-child[/max-connections-per-ip-per-minute[/max-child-per-ip]]]
user[:group][/login-class]
server-program
server-program-arguments
To specify an ONC RPC-based service, the entry would contain these
fields:
service-name/version
socket-type
rpc/protocol
{wait|nowait}[/max-child[/max-connections-per-ip-per-minute[/max-child-per-ip]]]
user[:group][/login-class]
server-program
server-program-arguments
There are two types of services that inetd can start: standard and TCP-
MUX. A standard service has a well-known port assigned to it; it may be
a service that implements an official Internet standard or is a
BSD-specific service. As described in RFC 1078, TCPMUX services are non-
standard services that do not have a well-known port assigned to them.
They are invoked from inetd when a program connects to the ``tcpmux
well-known port and specifies the service name. This feature is useful
for adding locally-developed servers. TCPMUX requests are only accepted
when the multiplexor service itself is enabled, above and beyond and spe-
cific TCPMUX-based servers; see the discussion of internal services
below.
The service-name entry is the name of a valid service in the file
/etc/services, or the specification of a UNIX domain socket (see below).
For ``internal services (discussed below), the service name should be
the official name of the service (that is, the first entry in
/etc/services). When used to specify an ONC RPC-based service, this
field is a valid RPC service name listed in the file /etc/rpc. The part
on the right of the ``/ is the RPC version number. This can simply be
a single numeric argument or a range of versions. A range is bounded by
the low version to the high version - ``rusers/1-3. For TCPMUX ser-
vices, the value of the service-name field consists of the string
``tcpmux followed by a slash and the locally-chosen service name. The
service names listed in /etc/services and the name ``help are reserved.
Try to choose unique names for your TCPMUX services by prefixing them
with your organization's name and suffixing them with a version number.
The socket-type should be one of ``stream, ``dgram, ``raw, ``rdm,
or ``seqpacket, depending on whether the socket is a stream, datagram,
raw, reliably delivered message, or sequenced packet socket. TCPMUX ser-
vices must use ``stream.
The protocol must be a valid protocol or ``unix. Examples are ``tcp
or ``udp, both of which imply IPv4 for backward compatibility. The
names ``tcp4 and ``udp4 specify IPv4 only. The names ``tcp6 and
``udp6 specify IPv6 only. The names ``tcp46 and ``udp46 specify
that the entry accepts both IPv4 and IPv6 connections via a wildcard
AF_INET6 socket. Rpc based services are specified with the ``rpc/tcp
or ``rpc/udp service type. One can use specify IPv4 and/or IPv6 with
the 4, 6 or 46 suffix, for example ``rpc/tcp6 or ``rpc/udp46. TCPMUX
services must use ``tcp, ``tcp4, ``tcp6 or ``tcp46.
The wait/nowait entry specifies whether the server that is invoked by
inetd will take over the socket associated with the service access point,
and thus whether inetd should wait for the server to exit before listen-
ing for new service requests. Datagram servers must use ``wait, as
they are always invoked with the original datagram socket bound to the
specified service address. These servers must read at least one datagram
from the socket before exiting. If a datagram server connects to its
peer, freeing the socket so inetd can receive further messages on the
socket, it is said to be a ``multi-threaded server; it should read one
datagram from the socket and create a new socket connected to the peer.
It should fork, and the parent should then exit to allow inetd to check
for new service requests to spawn new servers. Datagram servers which
process all incoming datagrams on a socket and eventually time out are
said to be ``single-threaded. The comsat(8) and talkd(8) utilities are
examples of the latter type of datagram server. The tftpd(8) utility is
an example of a multi-threaded datagram server.
Servers using stream sockets generally are multi-threaded and use the
``nowait entry. Connection requests for these services are accepted by
inetd, and the server is given only the newly-accepted socket connected
to a client of the service. Most stream-based services operate in this
manner. Stream-based servers that use ``wait are started with the lis-
tening service socket, and must accept at least one connection request
before exiting. Such a server would normally accept and process incoming
connection requests until a timeout. TCPMUX services must use
``nowait.
The maximum number of outstanding child processes (or ``threads) for a
``nowait service may be explicitly specified by appending a ``/ fol-
lowed by the number to the ``nowait keyword. Normally (or if a value
of zero is specified) there is no maximum. Otherwise, once the maximum
is reached, further connection attempts will be queued up until an exist-
ing child process exits. This also works in the case of ``wait mode,
although a value other than one (the default) might not make sense in
some cases. You can also specify the maximum number of connections per
minute for a given IP address by appending a ``/ followed by the number
to the maximum number of outstanding child processes. Once the maximum
is reached, further connections from this IP address will be dropped
until the end of the minute. In addition, you can specify the maximum
number of simultaneous invocations of each service from a single IP
address by appending a ``/ followed by the number to the maximum number
of outstanding child processes. Once the maximum is reached, further
connections from this IP address will be dropped.
The user entry should contain the user name of the user as whom the
server should run. This allows for servers to be given less permission
than root. The optional group part separated by ``: allows a group
name other than the default group for this user to be specified. The
optional login-class part separated by ``/ allows specification of a
login class other than the default ``daemon login class.
The server-program entry should contain the pathname of the program which
is to be executed by inetd when a request is found on its socket. If
inetd provides this service internally, this entry should be
``internal.
The server-program-arguments entry lists the arguments to be passed to
the server-program, starting with argv[0], which usually is the name of
the program. If the service is provided internally, the service-name of
the service (and any arguments to it) or the word ``internal should
take the place of this entry.
Currently, the only internal service to take arguments is ``auth.
Without options, the service will always return ``ERROR : HIDDEN-USER.
The available arguments to this service that alter its behavior are:
-d fallback
Provide a fallback username. If the real ``auth service is
enabled (with the -r option discussed below), return this user-
name instead of an error when lookups fail for either socket cre-
dentials or the username. If the real ``auth service is dis-
abled, return this username for every request. This is primarily
useful when running this service on a NAT machine.
-g Instead of returning the user's name to the ident requester,
report a username made up of random alphanumeric characters, e.g.
``c0c993. The -g flag overrides not only the user names, but
also any fallback name, .fakeid or .noident files.
-t sec[.usec]
Specify a timeout for the service. The default timeout is 10.0
seconds.
-r Offer a real ``auth service, as per RFC 1413. All the remain- ing flags apply only in this case.
-i Return numeric user IDs instead of usernames.
-f If the file .fakeid exists in the home directory of the identi-
fied user, report the username found in that file instead of the
real username. If the username found in .fakeid is that of an
existing user, then the real username is reported. If the -i
flag is also given then the username in .fakeid is checked
against existing user IDs instead.
-F same as -f but without the restriction that the username in
.fakeid must not match an existing user.
-n If the file .noident exists in the home directory of the identi-
fied user, return ``ERROR : HIDDEN-USER. This overrides any
fakeid file which might exist.
-o osname
Use osname instead of the name of the system as reported by
uname(3).
The inetd utility also provides several other ``trivial services inter-
nally by use of routines within itself. These services are ``echo,
``discard, ``chargen (character generator), ``daytime (human read-
able time), and ``time (machine readable time, in the form of the num-
ber of seconds since midnight, January 1, 1900). All of these services
are available in both TCP and UDP versions; the UDP versions will refuse
service if the request specifies a reply port corresponding to any inter-
nal service. (This is done as a defense against looping attacks; the
remote IP address is logged.) For details of these services, consult the
appropriate RFC document.
The TCPMUX-demultiplexing service is also implemented as an internal ser-
vice. For any TCPMUX-based service to function, the following line must
be included in inetd.conf:
tcpmux stream tcp nowait root internal
When given the -l option inetd will log an entry to syslog each time a
connection is accepted, noting the service selected and the IP-number of
the remote requester if available. Unless otherwise specified in the
configuration file, and in the absence of the -W and -w options, inetd
will log to the ``daemon facility.
The inetd utility rereads its configuration file when it receives a
hangup signal, SIGHUP. Services may be added, deleted or modified when
the configuration file is reread. Except when started in debugging mode,
or configured otherwise with the -p option, inetd records its process ID
in the file /var/run/inetd.pid to assist in reconfiguration.
[править] IMPLEMENTATION NOTES
TCP Wrappers
When given the -w option, inetd will wrap all services specified as
``stream nowait or ``dgram except for ``internal services. If the
-W option is given, such ``internal services will be wrapped. If both
options are given, wrapping for both internal and external services will
be enabled. Either wrapping option will cause failed connections to be
logged to the ``auth syslog facility. Adding the -l flag to the wrap-
ping options will include successful connections in the logging to the
``auth facility.
Note that inetd only wraps requests for a ``wait service while no
servers are available to service requests. Once a connection to such a
service has been allowed, inetd has no control over subsequent connec-
tions to the service until no more servers are left listening for connec-
tion requests.
When wrapping is enabled, the tcpd daemon is not required, as that func-
tionality is builtin. For more information on TCP Wrappers, see the rel-
evant documentation (hosts_access(5)). When reading that document, keep
in mind that ``internal services have no associated daemon name.
Therefore, the service name as specified in inetd.conf should be used as
the daemon name for ``internal services.
TCPMUX
RFC 1078 describes the TCPMUX protocol: ``A TCP client connects to a for-
eign host on TCP port 1. It sends the service name followed by a car-
riage-return line-feed <CRLF>. The service name is never case sensitive.
The server replies with a single character indicating positive (+) or
negative (-) acknowledgment, immediately followed by an optional message
of explanation, terminated with a <CRLF>. If the reply was positive, the
selected protocol begins; otherwise the connection is closed. The pro-
gram is passed the TCP connection as file descriptors 0 and 1.
If the TCPMUX service name begins with a ``+, inetd returns the posi-
tive reply for the program. This allows you to invoke programs that use
stdin/stdout without putting any special server code in them.
The special service name ``help causes inetd to list the TCPMUX ser-
vices which are enabled in inetd.conf.
IPsec
The implementation includes a tiny hack to support IPsec policy settings
for each socket. A special form of comment line, starting with ``#@,
is interpreted as a policy specifier. Everything after the ``#@ will
be used as an IPsec policy string, as described in ipsec_set_policy(3).
Each policy specifier is applied to all the following lines in inetd.conf
until the next policy specifier. An empty policy specifier resets the
IPsec policy.
If an invalid IPsec policy specifier appears in inetd.conf, inetd will
provide an error message via the syslog(3) interface and abort execution.
UNIX Domain Sockets
In addition to running services on IP sockets, inetd can also manage UNIX
domain sockets. To do this you specify a protocol of ``unix and spec-
ify the UNIX domain socket as the service-name. The service-type may be
``stream or ``dgram. The specification of the socket must be an
absolute path name, optionally prefixed by an owner and mode of the form
:user:group:mode:. The specification:
:news:daemon:220:/var/run/sock
creates a socket owned by user ``news in group ``daemon with permis-
sions allowing only that user and group to connect. The default owner is
the user that inetd is running as. The default mode only allows the
socket's owner to connect.
WARNING: while creating a UNIX domain socket, inetd must change the own-
ership and permissions on the socket. This can only be done securely if
the directory in which the socket is created is writable only by root.
Do NOT use inetd to create sockets in world writable directories such as
/tmp; use /var/run or a similar directory instead.
Internal services may be run on UNIX domain sockets, in the usual way.
In this case the name of the internal service is determined using the
last component of the socket's pathname. For example, specifying a
socket named /var/run/chargen would invoke the ``chargen service when a
connection is received on that socket.
[править] FILES
/etc/inetd.conf configuration file /etc/netconfig network configuration data base /etc/rpc translation of service names to RPC program numbers /etc/services translation of service names to port numbers /var/run/inetd.pid the pid of the currently running inetd
[править] EXAMPLES
Here are several example service entries for the various types of ser-
vices:
ftp stream tcp nowait root /usr/libexec/ftpd ftpd -l
ntalk dgram udp wait root /usr/libexec/ntalkd ntalkd
telnet stream tcp6 nowait root /usr/libexec/telnetd telnetd
shell stream tcp46 nowait root /usr/libexec/rshd rshd
tcpmux/+date stream tcp nowait guest /bin/date date
tcpmux/phonebook stream tcp nowait guest /usr/local/bin/phonebook phonebook
rstatd/1-3 dgram rpc/udp wait root /usr/libexec/rpc.rstatd rpc.rstatd
/var/run/echo stream unix nowait root internal
#@ ipsec ah/require
chargen stream tcp nowait root internal
#@
[править] ERROR MESSAGES
The inetd server logs error messages using syslog(3). Important error
messages and their explanations are:
service/protocol server failing (looping), service terminated.
The number of requests for the specified service in the past minute
exceeded the limit. The limit exists to prevent a broken program or a
malicious user from swamping the system. This message may occur for sev-
eral reasons:
1. There are many hosts requesting the service within a short
time period.
2. A broken client program is requesting the service too fre-
quently.
3. A malicious user is running a program to invoke the service in
a denial-of-service attack.
4. The invoked service program has an error that causes clients
to retry quickly.
Use the -R rate option, as described above, to change the rate limit.
Once the limit is reached, the service will be reenabled automatically in
10 minutes.
service/protocol: No such user user, service ignored
service/protocol: getpwnam: user: No such user
No entry for user exists in the passwd(5) database. The first message
occurs when inetd (re)reads the configuration file. The second message
occurs when the service is invoked.
service: can't set uid uid
service: can't set gid gid
The user or group ID for the entry's user field is invalid.
setsockopt(SO_PRIVSTATE): Operation not supported
The inetd utility attempted to renounce the privileged state associated
with a socket but was unable to.
unknown rpc/udp or rpc/tcp
No entry was found for either udp or tcp in the netconfig(5) database.
unknown rpc/udp6 or rpc/tcp6
No entry was found for either udp6 or tcp6 in the netconfig(5) database.
[править] SEE ALSO
ipsec_set_policy(3), hosts_access(5), hosts_options(5), login.conf(5), netconfig(5), passwd(5), rpc(5), services(5), comsat(8), fingerd(8), ftpd(8), rlogind(8), rpcbind(8), rshd(8), talkd(8), telnetd(8), tftpd(8)
Michael C. St. Johns, Identification Protocol, RFC1413.
[править] HISTORY
The inetd utility appeared in 4.3BSD. TCPMUX is based on code and docu-
mentation by Mark Lottor. Support for ONC RPC based services is modeled
after that provided by SunOS 4.1. The IPsec hack was contributed by the
KAME project in 1999. The FreeBSD TCP Wrappers support first appeared in
FreeBSD 3.2.
FreeBSD 9.0 January 12, 2008 FreeBSD 9.0
